With the continuous improvement of plastic properties, plastics are widely used in automobiles to make a variety of interior decorative parts, and now can be used to replace some metal materials to make certain structural parts, functional parts and exterior decorative parts. This not only meets the performance requirements of certain automotive components, but also meets the requirements of lightweight vehicles. At present, the percentage of plastic materials in the quality of the whole vehicle is 8% to 15%. The use of plastics in the automotive sector is no longer a new topic. The production and per capita share of automobiles have also increased substantially, and the frequency of scrapping and updating has naturally increased. In recent years, the recycling of used automotive plastics has attracted great attention from countries around the world. The relevant departments of the Chinese government have given great attention. As early as February 2006, the National Development and Reform Commission, the Ministry of Science and Technology and the State Environmental Protection Administration jointly promulgated the "Technical Policy for the Recycling of Automobile Products" to guide and promote the design and manufacture of automotive products in China. Work on scrapping, recycling and reuse. As an environmentally friendly material, plastic is widely used in the automotive industry due to its strong plasticity, light weight and high recycling efficiency. Plastics are increasingly used in interiors, exteriors, and functional structural parts. We cite a few typical types of plastics used in automobiles, and do a simple analysis of their crushing and recycling in manufacturing: ★ bumper, dashboard, etc. Difficulties: structurally shaped, large in size, containing glass fiber Bumper, instrument panel and other large-sized components, generally selected are ABS, PPO, PP, PVC and other enhanced engineering plastics. These components will increase the strength of the material by adding glass fibers. Therefore, the wear resistance of the pulverizer tool and the inner wall of the pulverizing chamber is relatively high during pulverization and recovery. In addition, the size of these components is large, and in order to improve efficiency during pulverization, most of them will use automatic feeding---------------automatic separation of dust----one-stop bagging Production line equipment, only need to invest 1 person, can complete the traditional work mode 3-5 personal work can be completed, and improve efficiency 30-50%. ★ Steering wheel, interior handle, door trim panel, door and window seals, fenders, etc. Difficulties: Elastomer soft rubber is not easy to cut Most of these components are made of PU (foaming), PVC artificial leather, TPV, plastic thermal elastomer, EPDM rubber, etc. These materials are characterized by elasticity, strong deformability and good hand feeling. In the pulverization and recycling, these materials present difficult problems such as soft rubber being difficult to cut, hot-sticking, agglomeration, and unloading. An elastomer-specific shredder must be used. Different from the ordinary pulverizer, this pulverizer is designed for elastomer and rubber. It has the characteristics of soft rubber in the tool material, cutting angle, rotation speed and tool shaft assembly method. The material can be quickly cut into granules and matched. Use a special screen to make the cutting smoother. For temperature-sensitive special elastomers and rubber (such as low temperature TPU, high purity PP, hot melt adhesive, etc.), low temperature environmental pulverization can be added to reduce the physical property changes caused by temperature rise. ★ interior, ceiling The ceiling is generally made of plastic fiber and plastic wool material. The fiber material is basically made of plastic material, so it can be crushed and crushed for further recycling. What should you pay attention to when recycling plastic fibers? Under the high-speed rotation of the cutter shaft, it is easy to be powdered; and the fiber material can only be crushed by shearing. Therefore, the crushing and recycling of such materials is different from ordinary hard plastics. It requires relatively high material requirements for crushing tools: ordinary hard plastics are generally brittle because of their high hardness. Pay special attention to the tool material and the choice of cutting angle. ★ headlights, lampshades The main considerations for the lamp and the cover parts are transparency and reflective performance, so the materials used are transparent PC, PMMA and so on. When crushing and recycling such materials, it is necessary to avoid contamination of the raw materials by the crusher body, and also to separate the dust generated in the crushing. If the powder is infiltrated into the transparent pellets, it is likely to cause yellowing of the product or black spots during molding. Ordinary shredders can be used, but dust removal is required. This type of material can be achieved by pulverizing with a conventional pulverizer, but it is preferable to add a dust removing device at the rear end of the pulverization. It is possible to remove more than 90% of the dust at the same time as the bag is pulverized, so that the performance and molding quality of the pulverized material are closer to the raw material when it is reshaped. ★ car control line Although the amount of control wire in the car does not account for such a large proportion of rubber, its recycling value can not be underestimated. Traditional recycling method: high pollution and low utilization rate The main components of the control line are PVC sheath and copper core. Recycling is only valuable if you separate the two materials. However, because these control lines are uneven in thickness and disordered, the traditional dialing machine does not work. The old recycling method is to incinerate the outer layer of PVC to obtain the internal copper wire. This method causes environmental pollution on the one hand and PVC plastic on the other hand. ★ Current recycling method: high cost performance and low pollution The copper-plastic separator is used to pulverize these messy control lines into rice grains, and then separate the PVC particles and copper particles to obtain clean PVC particles and copper particles. The separation cleanliness of the two materials can reach more than 99%. Can be directly reused separately, the entire process uses physical methods, does not change the performance of the material, and will not cause secondary pollution.
High Quality Solar Panels
our Solar LED Street Light use the 100% Solar Panel:Grade A polysilicon 4-6H EXPRESS CHARGINGPolycrystalline silicon solar panel, high photo-electric conversion rate
Solar street light Multifunctional design Inteligent high-brightness light source energy saving era IP65 Waterproof ,100w 300w 500W solar street light Application
Solar LED Street Light Widely use for Courtyard,road,wall,park,square,etc Solar led street light,solar led street split,split solar flood lights,solar lights. solar power light. Shenzhen You&My Electronic Technology Co., Ltd , https://www.ymledtrade.com
SMD5730 3030 2835 LED light source: high light efficiency and low light decay
TOUGHENED GLASS MASK
Toughened glass mask high hardness strong resistance
DIE-CASTING ALUMINUM LAMP BODYIntegrated die-cast aluminum housing waterproof anti-corrosion cold-resistant high-temperature resistant
Protection Rating ip65
multiple barrier seal design,rain and dust are seamless,easy to adapt to all kinds of weather
High Capacity Lithium Battery
Continuous lighting time up to 12 hours
rainy days can be used for 2~3days
INTELLIGENT LIGHT CONTROL
fully automatic sensing of weather changes ,no need to adjust automatic
charging during the day,automatic lighting at night,simpler lighting
/*kangxianyue 250*250 was created on 2017/3/29*/ var cpro_id = "u2939694";