Light partition wall partition construction installation color matching scheme construction bottom decoration construction knowledge The globe valve is used to cut off the flow of the medium. The globe valve is suitable for frequently opened occasions. The sealing parts of the globe valve are the disc and the valve seat. In order to make the globe valve close tightly, the mating surface of the disc and the valve seat should be grinding or using gaskets. The sealing surface can also be inset with bronze, stainless steel and other corrosion-resistant and wear-resistant materials. The disc and stem of the globe valve are connected with each other, so that the disc and stem are closely fitted. The lifting of the disc of the globe valve is generally controlled by the stem. The upper part of the stem of the globe valve is the handwheel, and the middle part is the thread and packing sealing section. The role of the packing is to prevent the internal medium of the valve body from leaking along the stem. Globe Valve,Globe Control Valve,Globe Valve Types,Flanged Globe Valve WUXI KVC-VALVE , https://www.wxkaiweixi.com
I. Pre-construction construction conditions: 
1. Check whether the framework meets the specifications and whether it meets the strength of the design standards.
2. Clean the work surface that needs to be performed on the floor and check the compactness of the floor.
3. No rough plastering was done on the wall. There was no construction work on the floor, and the floor must be kept clean.
4. The drawings of the place where the construction is to be carried out and the construction personnel should make the bottom. The construction personnel must be made aware of the construction process.
5. For personnel with special tasks, it is necessary to carry out serious audits and reach the height of the technical level to carry out the construction, and the construction responsibility shall be fulfilled.
Second, the construction arrangements:
1. In the case that quality can be guaranteed, a relatively complete management system needs to be established so that the work can be carried out in an orderly manner.
2. The construction preparation work must be in place. The requirements for technical personnel must be put in place. The power supply is a guarantee of safety. The problem of the line must be well implemented and the line must be installed. Material protection, entry materials must be strictly controlled, qualified for admission, equipment inspection should be careful, this can save equipment problems are timely functional replacement.
3, establish a quality control team, so that the material is not qualified for construction and use, the previous process does not clear the transfer of the next process can not start.
Third, the construction of lightweight partition board 1. Put the line, put the board in place, in the installation of lightweight partition board, respectively, the upper and lower plate thickness double line.
2. According to the specification of lightweight partition board, it can be cut with portable chainsaw.
3. Place cement mortar on the foundation and place the wall board to be installed on the foundation.
4. Sizing, apply the polymer mortar on one side of the edge of the two plates.
5. Installation, move the slats to be installed to the assembly position, correct the stencils with a spade, and tighten them tightly to make the polymer mortar full from the joints.
6. Adjust and use a wooden deed to hit the bottom of the wallboard to adjust it to a vertical level.
7. Correct, fix, check vertical with 2 meters or more than 2 meters, flat correction.
8. Grout, make up the pulp, fill up the wall of the wall after correction with polymer mortar, scrape flat, fill the gap with polymer mortar.
9. Fixed, with Φ6mm or Φ8mm steel reinforcements on the upper part of the wallboard, penetrated into the middle of the wallboard at 45 degrees, and the bottom was hit with a “7â€-shaped rebar into the concrete foundation and one end was driven into the wallboard.
Xiao Bian concludes: The above introduced the construction plan of lightweight partition board and hoped to help everyone. For more relevant knowledge, please continue to pay attention to this website information platform. Follow-up will present more exciting content for everyone.
The lightweight partition board is composed of gypsum, light steel slag, fly ash and other industrial waste slags, and is made by frequency-variable steam pressurization curing. The inner layer is equipped with a reasonable layout of thermal insulation, sound-absorbing inorganic foam profiles or other insulation materials. What are the lightweight partition wall construction plans ? Let's take a look at it right away.