Kitchen and ceiling
These diamond drill bits are made of industrial grade carbon steel with nickel-plated coated body to resist corrosion. A thicken diamond coating on the tops offers superior cutting strength for maximum drilling outcomes.
Each diamond Hole Saw has a smooth and exact finish that lower the incision resistance and drill pressure, increases the sharpness, and effectiveness of water lubrication. Excellent for making clean and precise holes on glass or ceramic and considerably extending Drill Bit life.
Perfect for drilling glass, tile, porcelain tile, ceramic tile, brick, and stone
These glass hole saw set along the drill bit facilitate the entrance of cooling water and escape of chips and other particles from drilling. Makes the drilling process easier.
diamond hole saw,hole saw,diamond hole cutter granite,diamond hole saw at harbor freight Behappy Crafts (suzhou)Co.,Ltd , https://www.craftsbehappy.com
Kitchen and ceiling techniques 1 Do not drill too deep The key to kitchen ceilings is to take advantage of the measures during the construction process, that is, when fixing drill holes, do not drill too deep. In the past construction, there was such a case. Because the drilling is too deep, the original waterproof capacity may be damaged, resulting in endless troubles. Therefore, it is recommended to keep 3-4 centimeters in diameter when drilling. 2 Correct installation sequence can reduce vibrations. Correct kitchen ceiling installation order can reduce unnecessary vibration . The correct installation sequence in bathroom is to install Yuba, exhaust fan first, and then do ceiling. Never install the exhaust fan or bathroom heater directly on the aluminum gusset plate with screws, and use the expansion bolts to hang directly on the concrete on the top;
The correct order for the installation of kitchen ceilings should be to first fix the hood of the hood and the flue , and to select the location where the hood is to be installed at the other end, and to buy the lights used in the kitchen, but do not need to install first. Then install the ceiling, then install the lights, it is best not to install large lamps directly on the ceiling. 
3 According to the construction plan, arrange the plate shape colors in order to install the keel. The direction of the keel should be determined according to the design trend of the ceiling measurement construction drawing. After confirming, the keel distance line and punching point should be marked on the roof, and the hammer Punching, drilling depth of not more than 4 cm, to prevent the destruction of embedded wires inside the wall tubes. After the punch is ready, expand the matching inner bulge into the hole. According to the height of the corners, the galvanized copper wire saw is good, into the inner bulge, according to the length of the room to cut the keel, the keel is fixed on the copper wire with a nut. The laying of ceilings should also be based on the measurement of construction drawings, the shape of the plate, the order of colors arranged in order, row plate, the pinch plate should be tight and seamless between the corners, and to indicate the control line hole. 4 When transporting piling, the aluminum buckle plate, plastic steel plate or integrated ceiling and supporting keel and accessories purchased when the plate is to be placed on the ceiling of the kitchen and bathroom shall meet the product quality requirements, and must be checked for bending deformation. In the process of transportation and stacking, the plates should be laid flat and not pressed, and high temperature and harmful substances should be avoided. When the keel is installed, it must be flat and the spacing deviation should be controlled within the allowable range. When installing, if the dimensions are deviated, it should be adjusted before inserting in order, and no hard insertion is required to prevent deformation. 
Kitchen ceiling order
The gussets must be tight and seamless. When installing the keel, the direction of the keel should be determined according to the design trend of the construction drawing of the aluminum buckle plate. After confirming, the keel distance line and punching point should be marked on the roof, and the electric hammer should be used for drilling. The depth of drilling should not exceed 4 cm. In order to prevent the destruction of pre-embedded wire tubes inside the wall. After the punch is ready, expand the matching inner bulge into the hole. According to the height of the corners, the galvanized copper wire saw is good, into the inner bulge, according to the length of the room to cut the keel, the keel is fixed on the copper wire with a nut. The laying of aluminum buckle plate should also be based on the measurement of construction drawings, the buckle plate, the color lined up in order, row plate, the buckle plate should be seamless with the corners, and to indicate the control line hole. 
Kitchen ceiling knowledge General kitchen ceiling installation needs to be done after the installation of the pipeline. For the kitchen ceiling project, the choice of materials is the first step in the project. The choice of materials will determine the quality of the ceiling in the future. At present, there are four types of ceilings in home improvement kitchens: pvc, gypsum, plastic steel plate, and aluminum buckle plate. 
1 pvc board to pvc as raw material, a very popular in the market a few years ago, but now because of encircling type problems, leading directly to the trend of exiting the market; 2 gypsum to be beautiful, generous, personality favored by many owners, but due to the difficulty of unloading Large, can not meet the continuous upgrading of the product, so the general community home friends will not choose gypsum ceiling materials in the kitchen and bathroom; 
3 plastic steel plate A high hardness, but the substrate is also made of plastic ceiling material, but because the steel plate market is not uniform, can not improve the product properties from nature to replace other materials, it can be said that the price is the only advantage of plastic steel. 4 Do not drill too deep a kind of metal aluminum buckle products. Combining high-quality metal aluminum as the basic material and perfect surface treatment technology, it has unparalleled advantages in terms of quality, individuality, vision, and embracing. At present, the aluminum buckle plate is based on perfect industry standards and products. Its own charm has occupied the main material status of kitchen and bathroom ceilings, but this product has always remained high in price and has become one of the hot spots in the market competition. Because of the fierce competition of this product, it is worthwhile to visit the market. 
In general families, the living room and bedroom can be ceiling-free, but the kitchen and bathroom are sure to be ceilings. Today, Xiao Bian talks about the kitchen ceilings.