Automatic lift rotary evaporator
The rotary evaporator always for distillation and extraction under vacuum pressure . The motor runs the rotation flask moving and heating water oil bath pass hot energy to the mixture of rotary flask . Then low boiling point of mixture will be heated and form a thin film and make evaporation . The lower boiling point mixture make morphological change from liquid to Vapor or hot air . Then hot vapor meet condenser cooling coil then become liquid again and fall down to collection flask .
Laboratory Chemical Vacuum Rotary Evaporators 1l 2l 3l 5l 10l 20l 30l 50l 100l
China Motorized Automatic Evaporator,Automatic Lifting Rotary Evaporator ,Electric Lifting Water bath Rotary evaporator Rotovap Manufacturers and Suppliers in China Zhongyi Kori(Zhengzhou)Equipment Co.,Ltd , https://www.korireactor.com
/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131"; Home>Bearing knowledge>NSK bearing repair method analysis Analysis of maintenance methods for NSK bearings
Bearing clearance /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';
When repairing the bearing under disassembly; firstly record the appearance of the bearing; recognize the residual amount of lubricant; after sampling; remove the bearing. The scavenger uses gasoline and fire oil throughout.
Removal of the removed bearing; coarse and fine washing; first place the metal mesh in the container; make the bearing not directly touch the dirt inside the container. When rough washing; if the bearing rotates with dirt; it will damage the bearing tumbling Face; should be paid attention to. In the rough wash oil; use the brush to go out to grease, adhesive; after cleansing; turn into fine wash.
Fine washing; the bearing is rotated while removing the oil; while carefully cleaning. Others; the oil should also be replaced frequently to keep clean.
Bearing repair and discrimination
Determine whether the bearing under disassembly can be reused; check after the bearing is removed; carefully check the raceway surface, the rolling surface, the condition of the cooperation surface, the wear condition of the cage, whether the bearing clearance can be added, and whether the scale accuracy is reduced. Damage, abnormal. Non-detached small ball bearings, etc.; use a single-handed flat end inner ring; rotating outer ring acknowledges whether it can be smooth.
Tapered roller bearings and other separate bearings; can be viewed from the rolling surface of the roll and outer ring.
Large bearings can not be rotated by hand; pay attention to the appearance of the rolling body, raceway surface, cage, ribs, etc. The higher the importance of the bearing, the more careful it is to view.
Determine whether the bearing can be used again; according to the degree of damage of the bearing, mechanical properties, importance, working conditions, viewing cycle, etc., the correlation is determined. However, if the following defects are found during the inspection; the bearing cannot be used continuously; the replacement of the new bearing is required. .
(a) There is a crack or a gap in the inner ring, the outer ring, the roll body and the cage.
(b) One of the ferrules and the rolling body is cracked.
(c) Significant abrasions on the rolling surface, ribs and roll.
(d) The cage is worn significantly; or the rivet is significantly loose.
(e) There are rust or scars on the raceway surface and the roll body.
(f) There are severe indentations or bumps on the raceway surface and the roll body.
(g) There is significant creep on the inner diameter surface of the inner ring or the outer diameter surface of the outer ring.
(h) Significant discoloration due to overheating.
(i) Bearings sealed with grease; seals or dust caps are severely damaged.
Recommend to friends comments close window Bearing related knowledge Common partial pain bearing anomalies imported bearing outer ring fixing method analysis centrifugal tightening machine has several bearings
Detailed analysis of the method of measuring the operating temperature of IKO turbocharged bearings by NTN bearing fatigue life, noise life and smooth life
This article links to http://
Please indicate the bearing network http://
Previous:The principle of bearing heaters: The details of "the reason for the early damage of imported NSK bearings"
Rotary Evaporator Rotovap vacuum distillation machines composite Rotating Evaporation Flasks, Glass Collection flasks, Cooling Condensers, Stainless steel Water Oil Bath and others
When you use rotary evaporator, you need set suitable distilation temperature and speed RPM
Ethanol Rotary evaporator can be for distillation, concentration, drying , recrystallation, extraction under refulux, gin application and beauty industries
Source: China Bearing Network Time: 2013-04-07