Many people tend to ignore the posture of our exterior walls when we are decorating. This has led to great changes in the exterior wall in a few years. Not beautiful. Therefore, everyone is both inside and outside. This decoration material is perfect. Let's take a look at the small pieces of the decoration house and the decoration house. What are the techniques for building exterior wall decoration ? Let everyone use it for reference. It is better to decorate the house.


建筑外墙装饰


First, what are the techniques for building exterior wall decoration?


1. Remember when constructing, it is required that the surface flatness deviation of the polystyrene board is not more than 5mm, which is also a very reasonable size. When it is out of tolerance, the protruding wall surface is polished, and the concave part is repaired. (The need to find the thickness of more than 6mm is 1:3 cement mortar plastering to ensure the flatness of the whole wall is within 5mm, the yin and yang angle is square, up and down smooth.


2. Master the preparation of mortar at the time of construction. Special bonding mortar and surface polymer anti-cracking mortar. This will help long-term use. During the construction, use a hand-held electric mixer to stir, (or manually stir) the viscosity of the bonded mortar is water: mortar = 1:5, while stirring with water; stirring time ≥ 5min, the mixing must be sufficient, uniform, moderate consistency, and Have a certain viscosity.


3. Under the understanding of the construction, after the mortar is finished, it must be allowed to stand for 5 minutes, and there is a period of relaxation. Stir again before use, and the prepared mortar should be used within 1 h. According to the construction drawing, the positioning line (middle line or side line) is ejected at the part where the EPS component is to be installed. Cut the EPS components according to the drawing installation dimensions. The EPS components are all standard sizes, and the seam width should be considered when cutting.


Second, the external wall construction precautions


建筑外墙装饰


1. It is very important to choose the product. The EPS component adhesive uses high-quality bonding mortar, so you have to have high-quality products. It is pasted by a thin layer full-stick method, and the joint width is not more than 3 mm. The bonding joint should be glued with the hook, the gray joint is full, and the surface of the EPS member is kept clean. Then press hard on the sticking part to make the glue overflow. However, the bonding strength of this method is worse.


2. Remember to stick firmly when constructing. The safety of the decorative thread (piece) is very important, which helps long-term use. In particular, the requirements of quality life-time system, it is mainly bonded with polymer mortar, not only has a long service life, but also has a firm bond, and there have been quality accidents caused by national standards and specifications and hidden dangers of anchor bolt corrosion.


3, the shape is free to process is also very good. Because it is the automatic cutting of computer design, it is necessary to pay attention to the style change, the line (piece) style is arbitrary, but the architect is worried about whether it will affect the realization of the facade effect. The EPS decoration line completely dispels the architects' concerns and designs it as desired. The shape is perfectly matched with the external thermal insulation wall.


The construction of the external wall also has a lot of knowledge. Everyone pays attention to it. This overall effect will be perfect. If you still want to know more about the decoration, please continue to pay attention to our decoration home website. Our website will continuously release decoration information.


More related wonderful reading:

Architectural exterior wall decoration materials

Building exterior wall decoration material

Building exterior wall decoration material


Red Light Therapy Device

We have been manufacturing and selling red light therapy device for 8 years and supply over 98% of these products to the European and American markets.

Red light therapy devices are widely used for the treatment of joint and muscle aches and pains and also have cosmetic benefits.

We manufacture and supply most of the red light therapy devices currently available on Amazon and look forward to working with you!

Red Light Therapy Device,Light Therapy Device,Joint Muscle Reliever,Handheld Led Light Therapy Device

Cangnan Younglite Electrical Co., Ltd. , https://www.younglitelight.com

Posted on