Coco chen    Office:+86-25-57909686 Coco chen    Office:+86-25-57909686 Screwdriver,2M Tape Measure,Cute Measuring Tape,Yellow Measuring Tape SHANGQIU CHAOYUE MEASURING TOOLS CO., LTD , https://www.calibrateds.com
Â
Cellphone: +86-18551609905
1.General introduction:
  Powder coatings are mixed with a certain proportion of the resin, fillers, curing agents and other additives, then prepared by hot extrusion ,crushed  and sieved.The products are stable at room temperature storage, then baking heat melted and solidified to form a smooth and bright permanent coating to achieve the purpose of decoration and corrosion.
Â
2.Feature:
          Â
1).The products are non-toxic, solvent-free and non-toxic volatile substances,
there are no intoxication, no fire, no "three wastes" emissions and other pollution problems, in full compliance with national environmental laws.Â
2).Raw material utilization is high, the highest utilization rate even more than
99%.Â
3).After being pre-coated handle, disposable construction, without primer,
you can get a sufficient thickness of the coating, easy to automate operation, high production efficiency, reduce costs.Â
4).Dense coating adhesion, good impact strength and toughness, high
coverage corners, with excellent resistance to chemical corrosion and electrical insulation properties.Â
5).Powder coatings storage and transport are safety and convenience.
  Â
3.Product series:Â
  Â
  The products include high light ( above 86%),glazed (76%-85%),matte(20%-50%),low light (below 20%). We also offer a variety of shiny products according to the needs of users.
Â
4.Powder physical properties:Â
Â
   Proportion : 1.2-1.8 (depending on the color and gloss ) .
Â
   Particle size distribution: 100% less than 125 microns (more than 85%         Â
   between 60 to 90).
   Liquidity(180°C):22~35mm.
   Curing conditions:200°C,10 minutes.
5.Average coverage:
8-10m³/kg, the membrane is 60μm
(calculate by 100% utilization rate of powder coating).
6.Packing:
   Carton packaging, lined with double polyethylene bag, net weight 20 kg.
  Â
7.Storage requirements:
   Store below 30 °C, ventilated, dry, clean room, not near the fire, heat, direct sunlight, open dumps is prohibited.Under this condition, the powder can be stable for 12 months, more than the storage period may be re-examined, such as the results meet the requirements, can still be used.
8.Health and safety:
Â
  This product is non-toxic. In the course of inhalation of dust should be avoided. The operators should wear  appropriate dust mask and glasses.
Â
9.Coating performance
Â
Coating performance
Test items
Inspection standards
Test indicators
High light
Glazed/Matte/Low lightÂ
Impact resistance
ISO6272
GB/T1732-1993
50kg/cm
40kg/cm
Cupping test
ISO1520
GB/T9753-1988
8mm
7mm
The adhesion (grid method)
ISO2409
GB/T9286-1998
0
Bending
ISO1519
GB/T6742-1986
2mm
3mm
Pencil Hardness
ASTMD3363
GB/T6739-1996
1H-2H
Salt spray test
ISO7253
GB/T1771-1991
>500 hours
Damp heat test
ISO6270
GB/T1740-1979
>1000 hours
Heat resistance
110°C/24 hours(white)
Good gloss retention,E≤0.3-0.4
Florida weathering exposure
ISO2810
South 45 °,12mons
Gloss retention≥50%
Artificial accelerated aging
60°C/8hours + 50°C/4hours condensing,cycle for 500hours
Gloss retention≥50%                         Color stability:E≤0.35
Â
Annotate:
1.The above experiment uses 0.8mm steel with degreasing and rusting, and the coating thickness are 50-70 microns.
Â
2.The above coating performance may be lower as shiny and slightly lower.
Â
Cellphone: +86-18551609905
1.General introduction:
  Powder coatings are mixed with a certain proportion of the resin, fillers, curing agents and other additives, then prepared by hot extrusion ,crushed  and sieved.The products are stable at room temperature storage, then baking heat melted and solidified to form a smooth and bright permanent coating to achieve the purpose of decoration and corrosion.
Â
2.Feature:
          Â
1).The products are non-toxic, solvent-free and non-toxic volatile substances,
there are no intoxication, no fire, no "three wastes" emissions and other pollution problems, in full compliance with national environmental laws.Â
2).Raw material utilization is high, the highest utilization rate even more than
99%.Â
3).After being pre-coated handle, disposable construction, without primer,
you can get a sufficient thickness of the coating, easy to automate operation, high production efficiency, reduce costs.Â
4).Dense coating adhesion, good impact strength and toughness, high
coverage corners, with excellent resistance to chemical corrosion and electrical insulation properties.Â
5).Powder coatings storage and transport are safety and convenience.
  Â
3.Product series:Â
  Â
  The products include high light ( above 86%),glazed (76%-85%),matte(20%-50%),low light (below 20%). We also offer a variety of shiny products according to the needs of users.
Â
4.Powder physical properties:Â
Â
   Proportion : 1.2-1.8 (depending on the color and gloss ) .
Â
   Particle size distribution: 100% less than 125 microns (more than 85%         Â
   between 60 to 90).
   Liquidity(180°C):22~35mm.
   Curing conditions:200°C,10 minutes.
5.Average coverage:
8-10m³/kg, the membrane is 60μm
(calculate by 100% utilization rate of powder coating).
6.Packing:
   Carton packaging, lined with double polyethylene bag, net weight 20 kg.
  Â
7.Storage requirements:
   Store below 30 °C, ventilated, dry, clean room, not near the fire, heat, direct sunlight, open dumps is prohibited.Under this condition, the powder can be stable for 12 months, more than the storage period may be re-examined, such as the results meet the requirements, can still be used.
8.Health and safety:
Â
  This product is non-toxic. In the course of inhalation of dust should be avoided. The operators should wear  appropriate dust mask and glasses.
Â
9.Coating performance
Â
Coating performance
Test items
Inspection standards
Test indicators
High light
Glazed/Matte/Low lightÂ
Impact resistance
ISO6272
GB/T1732-1993
50kg/cm
40kg/cm
Cupping test
ISO1520
GB/T9753-1988
8mm
7mm
The adhesion (grid method)
ISO2409
GB/T9286-1998
0
Bending
ISO1519
GB/T6742-1986
2mm
3mm
Pencil Hardness
ASTMD3363
GB/T6739-1996
1H-2H
Salt spray test
ISO7253
GB/T1771-1991
>500 hours
Damp heat test
ISO6270
GB/T1740-1979
>1000 hours
Heat resistance
110°C/24 hours(white)
Good gloss retention,E≤0.3-0.4
Florida weathering exposure
ISO2810
South 45 °,12mons
Gloss retention≥50%
Artificial accelerated aging
60°C/8hours + 50°C/4hours condensing,cycle for 500hours
Gloss retention≥50%                         Color stability:E≤0.35
Â
Annotate:
1.The above experiment uses 0.8mm steel with degreasing and rusting, and the coating thickness are 50-70 microns.
Â
2.The above coating performance may be lower as shiny and slightly lower.
Level: Finish Coat
Certification: ISO14001, RoHS, ISO9001
Substrate: Steel
Expiration Date: 1 year
Application: Electrostatic Spraying
Colors: Ral Color
Powder System: Polyester
Curing Condition: 180-200c/ 10-20minutes
Trademark: EVER
Transport Package: 25kg/Carton
Specification: SGS
Origin: China
Level: Finish Coat
Certification: ISO14001, RoHS, ISO9001
Substrate: Steel
Expiration Date: 1 year
Application: Electrostatic Spraying
Colors: Ral Color
Powder System: Polyester
Curing Condition: 180-200c/ 10-20minutes
Trademark: EVER
Transport Package: 25kg/Carton
Specification: SGS
Origin: China
Ral 9005 Satin Black Matte Finish Car Paint Powder Coating
More Detail Information, contact with:
Ral 9005 Satin Black Matte Finish Car Paint Powder Coating
More Detail Information, contact with: