At the end of the renovation, the installation of sanitary ware is an important project in this period. If the sanitary ware is not fully installed, it will cause considerable inconvenience to our use in future life. What is the order of installation and installation of sanitary ware? Let's take a look! Leading home decoration and maintenance platform First, the installation of the basin 1. The common basin is divided into two types: the basin along the basin and the basin without the edge. When installed, the edge along the basin should be placed on the table, and the edge of the basin without the basin should be close to the bottom of the table. 2. Before installing the basin, first check the height of the basin support beam. When installing, you can add Rubber Gasket at the bottom of the basin to level the treatment. When installing without a basin, it is necessary to fix it. 3. The part connecting the basin to the countertop should be sealed and sealed with a sealing paste to ensure that there is no water leakage or water seepage at the joint. Second, the installation of the toilet 1. Before purchasing the toilet, you should first understand the drainage method of your own bathroom and the pit distance of the toilet. Tell the merchant about this information when purchasing, so as not to buy the toilet. 2. When there is a deviation between the reserved drain and the drain position of the toilet, the reserved drain position is used to locate the toilet position. 3. When installing the water tank of the toilet, the center line of the toilet should be used for positioning. The gap between the water tank and the wall should be uniform, but it is best not to be larger than 20 mm. 4. The fittings in the water tank should be installed after the water tank is fixed. Third, the installation of the bathtub 1. Before installing the bathtub, first do the drainage test of the bathtub, close the drain outlet of the bathtub, and put water in the bathtub. After a period of time, see if the bathtub leaks. 2. When installing the bathtub, you must use the level to level the upper plane of the bathtub to ensure that the side of the bathtub is not inclined. The gap between the bathtub and the wall should be smoothed with a sealing paste. 3, in order to facilitate the life of the bath, the drainage of the bathtub, when installing the bathtub, at the water outlet of the bathtub, the position of the inspection port should be reserved. Fourth, the installation of the faucet 1. Before installation, first flush the water supply pipeline to avoid any debris in the pipeline and block the faucet. 2, the direction of the cold and hot water pipes must be careful not to reverse, under normal circumstances, the order is left hot right cold, that is, the left is the hot water pipe, the right is the cold water pipe. Adjustments can be made if there are special requirements. 3. When installing the water inlet hose, tighten directly by hand. Do not use tools such as wrenches, and do not wrap the sealing tape to avoid damage to the hose. 4. The faucet should be installed before the sanitary ware such as the bathtub. After the installation, unscrew the accessories that are easy to block before the faucet, open the faucet, and ensure that there are no impurities in the water pipe that are easy to block, then replace the accessories. Fifth, the installation of floor drain 1. The installation of floor drains should be carried out when paving the floor tiles in the masonry project. 2. The floor drain should be installed at the lowest point on the ground in the space. After the installation is completed, the floor drain should be blocked to prevent the construction waste from falling in during the decoration process, resulting in blockage of the sewer. Plastic,PVC,PP Breather Valve ; Vacuum Pressure Valves; Pressure Vent Valves;Air Evacuation Valve; Discharge Valve ; Evacuation Valve is used to discharge the air pressure inside of equipment and system when the pressure exceed the standard, and meanwhile let the air into the equipment when the pressure of system is vacuum to protect the system safety. Exhaust Valve/Vacuum Pressure Valve Breather Valve,Vacuum Pressure Valves,Pressure Vent Valves,Air Evacuation Valve,Discharge Valve,Evacuation Valve Ningbo RMI Plastic Co., Ltd. , https://www.rmiplast.com