All toilets must be used. Because of the flow of sewage and sewage, poor toilet installation can lead to leaks and odors at home. Therefore, the toilet installation must pay attention to this step. What are the steps for toilet installation and what should be noticed? Toilet installation process It is relatively easy to install the toilet, generally after buying it back, install it yourself or ask the worker to install it. Although the installation of the toilet is simple, it is very important to master the installation method of the toilet. Only the installation of an accurate toilet can be used with ease. Take a look at the general flow of toilet installation. 1, check the sewage pipeline and the ground level Before installing the toilet, the sewage pipeline should be inspected first to see whether there is muddy sand, waste paper and other debris in the pipeline. Check whether the floor of the toilet is horizontal. If there is uneven ground, install the ground. Leveling. 2, determine the center of the sewage pipe Turn the toilet upside down, determine the center of the toilet flush outlet, and draw a cross centerline. The centerline should extend to the feet around the bottom of the toilet. 3, fixed toilet Align the reticle with the floor drain outlet on the toilet and keep the toilet flush horizontally. Firmly press the sealing ring and install the anchor screw and decorative cap. 4, make the bottom seal Install a special sealing ring on the sewage outlet of the toilet, or put a circle of glass glue (putty) or cement mortar around it. The ratio of cement to sand is 1:3. 5, install the water tank accessories Drain the pipe for 3-5 minutes to ensure the cleanness of the water pipe; install the angle valve and connecting hose, then connect the hose to the inlet valve of the installed tank fitting and press the water source. 6, debugging and inspection Check the inlet valve water inlet and seal is normal, check the installation position of the drainage valve is flexible, there is no jamming and leakage, there is no leakage of the inlet valve filter device. Installation toilet precautions 1. Before the installation, the master should conduct a comprehensive inspection of the sewage pipeline to see if there is mud and sand, waste paper and other debris in the pipeline. At the same time, check whether the floor of the toilet installation is horizontal. If uneven ground is found, install the toilet. The ground should be leveled. Saw the outlet short and allow the outlet to be as high as 2mm-5mm above ground as much as possible. 2. The water outlet requires the installer to handle the leveling. The bottom of the toilet should be installed with a special flange for the toilet, or the glass glue should be applied evenly with the water outlet. The bottom of the toilet and the surrounding area should be glued. The gap between the toilet and the wall should be uniform and placed. Correct and stable. 3, after the toilet seat in place requires no leakage of water, water level is correct, flushing, flexible switch, cover solid. 4, now installed toilets generally do not install the anchor bolts, but use glass glue to plug the reserved holes in the toilet to prevent turning. 5. If installing anchor bolts, use a special sealant installed on the toilet to apply evenly at the outer 2CM of the toilet drain outlet. The water outlet of the toilet should be facing the central position of the drainage pipe. The position of the swell bolt on the right and left side of the toilet, take the toilet, punch, and bury the bolt. It should be noted that this newly punched swell plug pre-buried the hole and may break the waterproof layer. It is recommended to embed the expansion screws. At the same time, fill in the sealant around the hole, and then bury the bolt, first screw the expansion bolt, let the expansion bolt completely open, strengthen its pull, then screw the upper screw, put the toilet, Then directly screw the screw, cap, keep the overall appearance. In the meeting place between the toilet bowl and the ground surface, because the toilet bowl is not integrated with the ground surface, the seaming agent can be used. 6, the transparent sealant to stir, seal the toilet outside the mouth, so that it maintains the integrity of the surface with the floor, you can also part of the toilet water block in the toilet seat outside. 7. After the toilet is installed, wait until the glass glue (putty ash) or cement mortar is cured before using it for water release. The curing time is generally 24 hours. If you ask an unprofessional person to install it, usually to save time, the construction staff will use cement as the adhesive directly. This is definitely not enough to fill the fixed position of the bottom of the toilet. In fact, there is a drawback in the middle. The cement itself has expansive properties and takes a long time. This method may lead to cracking of the base of the toilet bowl and it is not easy to maintain. 8, install or debug tank accessories. First check the water pipe, discharge the water for 3-5 minutes to flush the pipe to ensure the cleanness of the water pipe; install the angle valve and connecting hose, then connect the hose to the inlet valve of the installed tank fitting and press the water source to check the water supply. Whether the valve inlet and seal are normal, check whether the installation position of the drainage valve is flexible and whether there is any jamming or leakage, and check whether there is any leakage inlet valve filter device. Acceptance of the installation toilet 1. Open the angle valve and check the connection for leaks. 2. Check whether the automatic valve opening and closing in the box is flexible. 3. Check the distance between the water level and the overflow pipe after the water in the tank is full. 4. Use both hands to hold the sides of the toilet, and shake firmly to observe if it is firm. 5. Put toilet paper in the toilet, open the plate hole to observe the flush, and check whether there is any leakage in each interface. No less than three consecutive blows, if the discharge is smooth, no leakage of each interface is qualified. Things that owners need to pay attention to in this step 1. Before you select the toilet, first determine the size of your house's water. What is the distance from the water outlet to the wall? (The standard is only 300, 400 mm two). 2, and then choose according to the size of your favorite style, pay attention to the choice of water-saving type (3-6 liters), order to see the model, origin, and now the products are mixed, shop around is no regrets choice. 3, before the installation of the toilet seat to determine whether your choice of products, accessories, instructions are complete, take a closer look at the instructions, understand some of the product issues, in order to prevent pilferage, cutting corners, remember. Toilet toilet decoration construction knowledge construction acceptance bathroom waterproof overall bathroom bathroom size bathroom leak Spider Grow Lights are an innovative full-spectrum LED lighting system designed specifically for indoor horticulture applications. Their unique, spider-like modular design features light bars that extend outwards, creating an even distribution of light essential for healthy plant growth. These energy-efficient Spider LED Grow Lights provide both cooling and full spectrum for the plants, making them perfect for hydroponic, aeroponic, and traditional soil-based growing systems. They are easy to install and a variety of light configurations for choices, 600W800W 1000W 1200W 1500W grow lights, providing efficiency and optimal lighting coverage. With their long lifespan, these Spider Grow Lights are the ideal grow lights for indoor plants, providing you with the best results for your plants. Led Grow Lights,Spider Grow Light,Grow Lights For Plant,Plant Lamp GuangDong One World High-tech Co., Ltd. , https://www.maksdep.com
Below is our wattage options, you can choose and request for details.
The meaning of installing a toilet