What is Emery Wear Floor? In fact, there are many around us. Because of its wear resistance and permanent corrosion resistance, it is widely used in docks, warehouses, parking lots, factories, bridges and other places. Here we will introduce: the construction process and precautions of Emery wear-resistant Flooring . Construction process: 1. Spread 2/3 of the total amount for the first time and compact the bristles with a polished disc. 2. Spread 1/3 of the total amount for the second time and use a lighted disc to compact the bristles. 3. After the initial setting, wipe it with a calender. 4. Check the flatness of the material after spreading, adjust the material in a timely manner, and compact the armpits and wipe the light. 5, before finishing, polishing with a trowel machine to achieve the completion of the process; 6, according to the requirements of curing agents such as ground wax and other glazing. Due to the material characteristics, the corundum wear-resistant floor board must be damaged by the outside world during use. Due to wear, water erosion, weathering, etc., the corundum wear-resistant floor surface will appear gray, powder and other phenomena, seriously affecting the floor The appearance and service life, therefore, are now generally hardened against the hardened anti-corrosive flooring, allowing it to extend its life by 30 years. Construction Notes: 1: The control of the construction time of emery wear-resistant floor materials is very important. Special attention must be paid to the preparation of sufficient manpower, equipment and staff to perform continuous operations when the primary concrete reaches the construction conditions. 2: During the construction process of emery wear-resistant flooring, it is not advisable to add extra moisture, otherwise it may affect the quality of emery wear-resistant flooring. 3: Color corundum wear-resistant floor light collection times of the cement color Corundum wear-resistant floor to less twice, because the number of received light too much, will deepen the color of the area, prone to color. General cement color corundum wear-resistant floor received light 5-6 times, color corundum wear-resistant floor 4-5 times. 4: Disposal of the edge of sub-warehouses: In the construction of sub-bins, the scum splashed by the trowel on the edge of the sub-warehouse should be timely cleaned to prevent the floating slurry from affecting the aesthetics of the sub-bining joint. 5: Under normal circumstances, the corners of the construction block and the horizontal kerfs will bear more severe wear and impact. These parts must take additional protective measures before surface treatment. The protection method can be one of the following methods; a. After the concrete has been leveled, spread the diamond emery wear-resistant flooring material within 10 mm wide along the construction edge, and the sprinkling rate is 5 kg/m2. Use a spatula to apply the emery wear floor material to the concrete surface. b. After the concrete has been leveled and leveled, a 10 mm deep V-notch shall be dug along the construction edge, and a small amount of water shall be added to the corundum-resistant floor material to make up the viscous mortar and make up for compaction to ensure that it is bonded with the basement concrete. . Editor's summary: The construction process and precautions for the emery wear-resistant flooring were introduced. I hope I can help you. For more information, please pay attention to this site. Floor anti-slip floor tile
Melamine Laminated MDF board is mainly used for laminate floor, door sheet, partition, furniture, decoration of indoor&outdoor, office and home furniture, sould equipment, inside decoration of the car, antistatic floor of computer room, panel, security door, wall board etc, and also used for the package and the basic material of laminate Wood Flooring .
Melamine Laminated MDF Board is easily for coating finishing, every coating, oil paint are also on the surface of Melamine Laminated MDF , is the fist choice as the basic material of painting effects.Melamine Laminated MDF is one kind of beautiful material of decoration. Smooth and flat surface, fine texture, steady property. All kinds of venner, gummed paper, light metal plate, melamine paper etc, is also can on the surface of the Melamine Laminated MDF. Melamine Laminated MDF is made from acoustical board after drilling, is used in construction decorative progress, such as meeting room, displaying room, office etc. And we have Furniture Melamine MDF Board.
LULI Group Corp. Ltd, well known as the leading manufacturer for wooden, steel and paper products, located in Shouguang, Weifang, Shandong, China. Since the foundation in 1985, it focus on the production of Plywood , venner,MDF board, Particle board, Door skin , Blockboard , Finger joint board, OSB , paper, Steel etc.
Melamine Mdf Details:
size:1220*2440MM 1830*3660MM 1830*2440MM 915&610*3660MM 1220*2800MM 1525*2440MM
THICKNESS:2MM-35MM
MATERIAL:POPLAR, COMBINE, PINE
GLUE:E0, E1, E2, FIRE-PROOF
CERTIFICATION:CARB, FSC, CE, SON CAP
Melamine MDF Melamine Laminated MDF,Plain Melamine Mdf,Melamine MDF Board,Furniture Melamine MDF Board Luli Group Co.,Ltd. , https://www.cnluli.com
