Tiles are an essential building material in modern home decoration, and the use of ceramic tiles makes our home decoration more perfect. Tiles have a strong decorative effect on the home. Tiles are fire-resistant metal oxides and semi-metal oxides that are mixed, pressed, ground, glazing, and fired. The raw material of the tile is mainly made of a mixture of clay and quartz sand. Here we will introduce to you: how to paste the family tiles and the acceptance criteria of the tiles. How to paste family tiles: One: tiling installation knowledge 1. Before the concrete floor tiles are laid, the base layer should be cut and the depth of cutting hairs should be 5-10mm, and the spacing between the cutting hairs should be about 30mm. After that, clean the floating ash, mortar, and oil stains, and produce scattered water to sweep the ground. 2. Before the tiling, a good line should be played. A reference line at right angles to the doorway opening should be ejected on the ground. The line should start from the doorway to ensure that the entrance is a whole brick, and the non-whole brick is placed under the overcast angle or under the furniture. The vertical and horizontal positioning control lines appear. Two: Tile installation order The order of the general tiling: the first posted wall tiles, after the paste floor tiles. First paste the inner house and post the outer house. Three: Tips for installing tiles 1. Tiles If ceramic tiles are used, ceramic tiles should be soaked in the shade. 2. When tiling, the cement mortar should be thoroughly applied to the back of the ceramic floor tile. At the same time, use a level ruler to check and correct and wipe the surface cement mortar. 3. After the tiles are finished for 2 to 3 hours, use white cement to wipe the joints. Use cement mortar and sand=1:1 (volume ratio) cement mortar. The joints should be densely filled and smooth. Wipe the surface with cotton again. Four: How to supervise the installation of ceramic tiles Tile construction speed: a good tiler is posted 5-6 squares a day, otherwise it is difficult to ensure quality. Especially in the case of windowsills where small diagonals are needed, it is time consuming. Tile surfacing acceptance criteria: 1. Pay attention to whether tiles need to be parqueted or laid in a uniform direction. 2. The leveling of floor tiles shall be checked with a 2-meter level ruler, the error shall not exceed 0.5 mm, the height difference between adjacent tiles shall not exceed 0.5 mm, and the gap straightness shall be 3 mm. When laying the floor tiles, other types of work shall not be polluted and shall not be trampled. After the tiles are finished, they will be sewn 24 hours after the completion of the floor tiles, cleaned, and cured. 3, Floor tiles emptying phenomenon is controlled within 3%, the empty channel on the main channel must be reworked, 3% single refers to a single piece of empty corners, the whole block must not empty. 4. After the tiles have been finished, check whether the flatness has any errors, empty drums, or color differences. Cover them with cardboard or plywood, old carpets, etc. The gap between the boards must be tightly affixed with a wide paper tape to prevent debris from entering. 5. Under normal circumstances, the levelness of the floor tiles is allowed to have an error of 2mm, the gap of the floor tiles must be the same, the corners of the bricks and bricks should be leveled (0.3mm error is allowed), and the bricks and bricks of the kitchen and bathroom wall tiles are The corners should be flat, but also need to be level (allowing 1mm error) and verticality (allowing 2mm error) to be achieved. Bathrooms and balconies need to be floor drained, and the slope should be put first. If there is no special reason, there must be no Water. Editor's summary: The acceptance criteria for how to attach a ceramic tile to a tile is introduced here. Hopefully it will help you. For more information, please follow this website. Tile tile brand tile Material :Natural slate , quartz,sandstone ,marble etc . Mushroom Stone,Mushroom Stone Panel,Wall Stone Cladding,Slate Wall Cladding HEBEI DFL STONE , https://www.dflstone.com
Size :15*60*(1.0-2.0) cm .Can also be 10*40*(0.8-1.2)cm ,15.2*61*(1.0-2.0) or 20*(60-5)*(2-4)cm
Shape :Rectangle ,interlock ,mushroom etc.
Packing :Hard carton then fumigated strong wooden crate.
The wooden crate size is made as the container size . After loading the wooden crate in the container ,the wooden crates will nearly same size with the width of the container .It can make the wooden crate not have space to move during transport . In this case ,it can keep the stone safety mostly
Application : Can be used to decorate the outside wall or inside wall .Decorate your house ,decorate your life .