Hood installation meaning As the saying goes, it's a matter of hands-on, abundant clothing. Hoods are one of the essential items in modern kitchens. It is critical to purchase good hood products. However, the installation position, height, and firmness of the hood, etc. directly affect the effectiveness of the suction and exhaust fumes. Therefore, it is also very important to ensure that the hood is properly installed. Although the installation of hoods generally requires the help of the workers, it is possible to ensure that the kitchen is refreshing and beautiful and to understand basic installation knowledge. Hood installation process Although there are many product types of the hood, the basic process for installing the hood is basically the same. Here's an example of side-suction range hood installation with a small series to see its installation process. 1, determine the hanging plate installation position The installation position of the hood is directly above the stove and the cooker on the same axis line, the top end of the range hood range from the height of the stove surface is 65-75cm, the side suction hood to the stove surface is 35-45cm. According to the size of the specific hood product, find the position where the gusset is installed on the back and use a pencil to draw the line. In addition, if the installation position of the hood is still a certain distance from the top, in order to hide the smoke tube, the hood extension hood can be customized, and before the installation, the position of the hood extension board must be extended. 2, drilling installation hanging plate After determining the installation position of the hanging plate, drill a hole with a depth of 5-6 cm in the installation position with a percussion drill, press the expansion tube into the hole, and secure the hanging plate with screws. 3, hang the hood to the hanging plate The style behind the hood coincides with the hanging plate so that the hood can be hung. Because the hood is generally heavy, it usually takes two people to cooperate when hanging. 4, install the exhaust pipe Insert the exhaust pipe into the notch between the inner and outer rings of the outlet of the check valve and fasten it with screws. The other head extends directly into the outdoors through the reserved hole. If the exhaust pipe is to be connected to a common flue, it must be connected with a common flue anti-return check valve and sealed. If the smoke is exhausted outside the wall, it is advisable to install shutters outside the exhaust pipe to avoid recharging. 5, install extension hood This is only for products that require an extended hood. As mentioned earlier, if you need to install a lengthened cover, you must first install the hanging plate. Then, with the hood and the exhaust pipe installed, an extension hood is attached. 6, install oil cups and other accessories Then there are only oil cups, masks, and other accessories left on the hood. After the accessories are installed, the hood is installed and the basic installation is completed. Hood installation precautions 1. Installation height and position: The installation height of the hood should not be lower than 65 cm above the stove top, ie the distance between the hood floor and the gas cooker should be between 65 cm and 75 cm. Be sure to install it on the vertical of the stove. Above, should not miss the stove. Also, try not to install the hood near doors and windows where the air convection is strong, so as not to affect the effect of smoking; 2. Reserve power position: When setting the power supply position for the hood, be careful not to overlap with the punching position of the hood and the position of the trim board; 3, non-return valve: Check valve must completely block the flue hole, otherwise there will be fumes against the reverse, after installing the check valve must be confirmed after opening and closing can be installed into the outlet pipe; 4, a high degree of attention: high kitchen when installing hood may appear decorative panel height is not enough; 5, drilling attention: before the installation of the hood must be confirmed that there is no hole in the drilling area, gas pipes, wires, in order to avoid damage, or even cause electric shock hazards; Hood installation acceptance Use the switch repeatedly to see its flexible effect. If you touch the exterior with your hand, do you feel that there is a slight leakage of electricity? Run the hood and listen to it for noise. Especially for the two fans, honestly, this product is generally nothing. questionable. Things that owners need to pay attention to in this step 1, must require installation workers will hood installation level, no tilt; 2. After the installation is complete, you must try the machine and find out that the problem should be raised immediately; 3, check valve is very useful, even if you need to pay an additional charge should also be installed; 4. Try to shorten the distance between the hood and the public stack so as to obtain the best smoke emission effect. If the smoke is discharged to the shared flue, do not insert the flue pipe into the smoke too deep and the resistance of the flue gas increases. If it leads to the outside, be sure to extend the exhaust nozzle by 3cm. Smoke exhaust pipe should not be too long, it is best not to exceed 2 meters, and minimize bending, avoid multiple 90-degree bend, otherwise it will affect the effect of smoke. 5, after confirming that there is no mistake, pay attention to fill out the hood warranty card, which is important information needed for future maintenance. The above is about the hood installation and acceptance of the relevant content, read these, you are not for the hood installation method and acceptance notice more understanding of it? If you want to install your own hood, you may wish to refer to the above method and work! If you still have something that you do not understand, please leave a message and we will answer your questions as soon as possible. For more information, please follow this site! Hood construction acceptance decoration construction knowledge Flow Cells,Flow Cell Cuvettes,Fused Black Quartz Cuvettes,Micropore Flow Cells Yixing Jingke Optical Instruments Co.,Ltd. , https://www.jkgxcn.com
