Three trees paint entrance decoration paint latex paint window switch floor tile cabinet door
Wood plastic outdoor wall panel
Welcome to our product page of WPC Wall Panel, in which you can find detailed information of Outdoor Wall Panel. Our Outdoor Wall Panel is good in quality and competitive in price. We are manufacturer and supplier of Wood Plastic Composite Wall Panel. We export Outdoor Wall Panel. We supply OEM service of Outdoor Wall Panel for you. We would manufacture Outdoor Wall Panel following your specific requirement. We are looking forward to your E-mail and establishing cooperative relationship with you! We would provide professional WPC Wall Panel Decking with good services for you!
WPC Wall Panel Wood Plastic Composite Wall Panel, WPC Wall Panel, WPC Wall Panel Decking Shangyu YongSheng New Material Co., Ltd. , http://www.wpc-deckingboard.com
1. The old house must be cleaned out (except for new houses and intact old paint). Check the original base with 2M ruler before ashing, if the error exceeds 5mm, use talc plus white cement or gypsum powder to level.
2, the gypsum board base, with plaster joints, and then paste kraft paper or special bandages. The special screw on the gypsum board must be filled with anti-rust paint.
3, layer base must first brush alkyd varnish, using wood glue or putty jointing, and then paste kraft paper or a special bandage, not blistering.
4, the first time putty can use 1-1.5M on the ruler to scrape, yin and Yang angle must be through the ink line to find the verticality and flatness. After the putty should be completely dry before the construction can be done.
5, the second putty treatment wall surface, should reach a large surface smooth, smooth, flatness with 2 meters on the ruler check, large surface should be ≤ 3mm.
6, the third putty for local search, with a 200-watt bulb or 800-tungsten iodine lamp side of the light to check the flatness, find fill.
7. When scraping putty, try not to contaminate other types of work and keep the construction process and site clean.
8. When the construction personnel of the paint coat are ashing at a high place, a horse bench and a springboard should be used, and trampling on wooden works is strictly prohibited. Scaffolding is safe, reliable and easy to use. If the floor or floor tiles have been constructed and the paint is to be re-applied, the stool must be protected before being used.
9, before the construction of latex paint, the use of paper tape to the edge of the door, the edge of the cabinet and other places with the latex paint protection, will be cleaned after the wall of dust can be cleaned.
10, latex paint construction primer again, topcoat twice. After brushing the primer, use a primer to adjust the putty to make up for it.
11, when the above paint, water should be mixed according to the actual situation, evenly, add water up to no more than 20%, too few prone to brush marks, too much hiding power is not enough.
12. If the top coat is to be applied with a brush, it should be brushed from the top to the bottom in the vertical direction and then brushed vertically in the vertical direction. Brushing the topcoat must not present any obvious brush marks, and no runny phenomenon may occur. Painting should be done from top to bottom, with the walls behind the ceiling, and the same area should be completed continuously.
13. If you need to pause during the brushing process, the brush or drum must be soaked in the paint or water in a timely manner. Immediately after the brushing is completed, wash all the utensils with clean water and put it to rest.
14, the second time the topcoat should be carried out after the top coat is completely dry, at least two hours apart. The latex paint construction room temperature should be above 5 degrees Celsius. At the same time, the doors and windows are closed to reduce the air circulation. After 2 hours of painting, the windows can be ventilated.
15, latex paint topcoat, other types of work can not be constructed to prevent pollution. Pay attention to finished product protection (ground and adjacent finished products). Lacquer paints that fall on other decorative finishes should be cleaned.
16, after the construction of latex paint, should pay attention to product protection, not hanging wound, especially light and mercerized latex paint should pay attention to, because there are light and mercerized latex paint brush easily appear after the "flower" phenomenon. If latex paint is used for spraying, special spraying equipment must be used to spray it twice. The second time of spraying should be two hours after the first pass.
Acceptance Criteria:
1, no brush pattern, flow fall.
2, feel smooth, smooth, no block feel, no obvious grainy.
3, no off powder, peeling, crack phenomenon.
4, no bottom, anti-alkali, biting color, uniform color.
5, not contaminated other types of work (and wood, switch panel, etc. must be tight, smooth interface, no seams not brush and pollution).
6, when the latex paint line decoration, the line texture should be clear, through.
Wood plastic outdoor wall panel Features
1. Environmentally-friendly wood wall panels, 100% recyclable.
2. Flame retardant, the invisible change, the age of 15 years.
3. Does not contain formaldehyde, Lead, Mercury and any other harmful substances.
4. A variety of colors, comes with lines, random lines, and in-depth product mechanism, real touch.
5. Simple installation, provincial, effort, labor.
6. Suitable for outdoor use, UV resistant, anti-aging.
7. Pest control, anti-static, anti-mildew.
Xi'an Decoration Classroom latex paint engineering construction process and process